Відео

Will try tommorow

This is the very best 987 convertible top transmission repair video!

It feels great to bring those motors back to life, and saves you a ton of money(at least $80 an hour +parts). Congratulations!.....AL Scott

I Watch the entire video..lots of muscle due to the inconfortabil position to work…since you drop just about everything….maybe dropping the entire thing and rebuild it out of the car would be easier….then ask a friend to help you lift it up might be a better way to do it? Any advice?

the gaskets are leaking on my Venza, even though it has metal lines. This could be quite the challenge to do without a lift

thanks i have a clk 350 .How long is the treatament duration?

Thanks for the video, Did you try to change the led light from amber to white, if yes how? thanks

Hello, can you advise if and how you removed the sunroof manual shade? I want to remove this to re-trim it but I'm struggling to figure out how this is done.

Hello, could you tell me which cables you connect to 12v so I can test the box? please!!

Hello, I was following your tutorial and I believe I messed up the board, is there any way I can speak with you? Thanks

Excellent

Love how you need to dismantle half the car to swap door trims😖 Thanks so much for the inside look at everything❤

I had both issues on my ’05, (climate control switches needed to be replaced and spoiler button not working) and just did this project. It took me about 2.5 hours. This video was very helpful and I'm very happy to have a great looking center dash. Regarding the removal of climate control switches, I didn’t understand until I struggled with it for several minutes that the tiny tabs must be broken off the switch and at the same time, the two long levers need to be pushed apart from each other, in order for the switches to be released. Use two tiny screw drivers or tweezers to separate the levers and a tiny screwdriver to break the tabs. As far as the spoiler button, the module does not unscrew to expose the inside, unlike the climate control module, which you can unscrew. This module has one-way tabs. I was not able to pry it open, for fear of causing irreversible damage to the module, so I didn’t proceed with that part of the fix.

Man thank you so much I was so affraid to toch this thank you

I finally got around to replacing my cluster LCD. It's a bit of a pain to do without the proper tools and probably with the proper tools. 10/10 recommend getting the repair service instead... It took me about 5 hours. The older stepper motors with the black dots on the back are better in my opinion. I had a cluster from a 1995 e38 that I was able to take parts from. The cluster is somewhat different in that the redline is higher and the coolant temp gauge has a line in the middle to show the ideal operating temp, but the stepper motors are the same. The needles seemed easier to remove from the older cluster seeing as I was able to remove them without damaging the motors. Oh, and the black and white fuel economy stepper motors are the same as far as I can tell. I was able to pry the needles off of both. After changing the LCD, I noticed the light to show if the mileage has been altered is lit. I'm not sure exactly what caused that. It may have always been on before but I couldn't tell because of the dead pixels. I changed the LCM when I first got the car and I never had it coded. I remember the mileage flashed to over 200k, so I turned the ignition off and on again and the mileage went back to 130k I've driven the car across the country a few times since then.

The videos for information. No need for music

I have changed it but it doesn’t go!

Helpful video, appreciate the walkthrough, doing mine shortly 😅 The only thing I don’t understand is how marking the nuts on the strut mount helped lining it up when you reinstalled it. Is there a lot of wiggle room in the mounting holes?

Hello, you repair pictures. I have a problem with the pixels of the kilometers and the 5 engines to change the old owner. I try to disassemble it and I'll charge it.😢😢

Vert good video, Sir. I watched about 10 of similar jobs, with Highlanders, RX 350s, and Venzas, etc. l find your camera has the best angles, lighting, and details. I also appreciate you took the time to show every step of your work and the patience to explain them! Thank you 👍🎊

hello, it's great how you fixed it 👌 please where can I buy the replacement display. it is nowhere in the store. please contact me. thank you in advance 🤝🤗

Great video,, did you put it back together?

Great job!

Would this be able to be done with the engine in the car?

2011 here Just failed and I'm glad my wife caught it leaking before it ran dry!

5/8-11 die, and a 5/8 3-4inch coupler and your all set, no welding required

Hello Thank you for this Video - this helps really. Greetings from Germany

Great video very helpful

What has this got to do with replacing the INLET valve?

you are a brave man. bro

video is very clear and helpful.

I ordered bushings for my car, and they didn't fit. I needed the ones like you have. LOL

Car care nut's channel mentions to not get brake cleaner on o2 sensor. May ruin sensor.

Great video.

Thanks for showing this, but WD40 does literally nothing to help remove bolts. Liquid Wrench and whack it with a hammer. Works best if you have time to spray, hammer it, and leave it for a little while. Amazing stuff.

Where can i get the flux you use and the solder

In uk the valve is positioned in the actuall water feed pipe that connects to your water inlet tap.

I did it. Thank you so much for this video, excellent! Saved me an significant amount of money, Mercedes was asking for. The repair kit was just 12,68 EUR. The rapair a satisfying day together with my brother. 🔧🪛👍

How applicable is this to a w208?

Do you know what voltage are the turn signal LED? Thanks for this video!!

I have to say this is possibly the best Vid on replacing the starter motor I have seen.......excellent I really really learnt something, fantastic

Excellent video. The extra advice about the pump and water level is very helpful.

Thank you for this video !

I pulled the gas cluster needle out and the wire came out. I know I messed up, is it fixable ?

How does the top come down if the window won't drop?

Bez ciebie nigdy bym nie doszedł co i jak, dziękuję bardzo za film, nic nie rozumiałem ale wszystko widziałem (Polish)

Thank you . Very helpful . My bumper was in two pieces from back impact . I was able to fix it with fiberglass bondo .

Where do you get the service manual?

how did you get the update software?